員.png)
QQ交談
您所在位置：請輸入產品關鍵字：
郵編：523000
聯系人：楊小姐
留言：在線留言
商鋪：http://m.mividagoldenbeach.com/st101985/
日本SMC消音器選型資料下載
最近更新時間：2017-4-14
提 供 商：東莞市金瑞工業自動化設備有限公司（東莞市工搜電子有限公司）資料大小：394.3KB
文件類型：PDF 文件下載次數：113次
資料類型：未知文件瀏覽次數：362次
日本SMC消音器選型資料下載
Caution 1. The silencer clogging may result in a blocked exhaust port. Provide a safety design so as not to cause the whole system to malfunction. Selection Caution 1. When selecting the silencer, the sonic conductance (including combined sonic conductance) of the silencer should be larger than that of the solenoid valve. Sonic conductance C [dm3 /(s·bar)] = Effective area [mm2 ] ÷ 5 2. Use within the range of specifications. Operating Environment Warning 1. Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. Refer to the construction drawings for silencer materials. 2. Avoid exposure to direct sunlight. 3. Do not operate in locations where vibration or impact occurs. 4. Do not use the product in locations where it is near heat sources and exposed to radiation heat. 5. Do not use in an environment where the product is exposed to cutting oil, lubricating oil, or coolant, etc. If it is used in an environment where there is possible contact with cutting oil, lubricating oil, or coolant, exercise preventive measures. 6. Do not use in an environment where foreign matter may stick to the product or get mixed in the product’s interior. It may result in clogging at an early stage, coming off or causing damage. Caution 1. The silencer is intended to reduce the noise of compressed air that is exhausted from the pneumatic equipment. Since noises generated by sources other than the exhaust, such as noise generated inside piping, equipment vibration and solenoid valve switching, cannot be reduced, locate the cause of these noises and take countermeasures. The product does not function as a filter. Do not use the product as a filter regardless of negative and positive pressures. 2. If the compressed air supply is contaminated with fluids such as oil and oil mist, such fluids will be dispersed to the environment. In such a case, an exhaust cleaner is recommended to recover fluids and reduce noise. 3. The value of the noise reduction may vary, depending on the pneumatic circuit or pressure that is exhausted from the solenoid valve. 1. If the silencer body is made of resin and is tightened too much, the silencer may be damaged. 2. Tightening by using a pipe wrench or pliers may cause damage to the silencer. This method is not recommended. Please follow the procedures below for mounting. !When the body is made of resin Hold the tip of the body (the side without thread) and screw it in. At the point where the thread begins to feel tight, use a wrench on the hexagonal flats to tighten an additional 1/4 turn. Tighten the AN05-M5 by hand compley until the ends of the fitting come into contact with the mounting surface. Then apply additional tightening. Note that the additional tightening s
日本SMC消音器選型資料下載
SMC 新型消音器AN體積更小，消音效果更好，增加M5螺紋連接、快插方式連接，具有樹脂體和金屬體兩種材質……